Thermostat Guide

Before submitting a Maintenance Request for the temperature in your room/unit, please read through the information below, to be sure you are setting and adjusting your thermostats properly. If you have followed the directions as written, but are still experiencing issues in room temperature, please contact our Facilities staff by submitting a maintenance request.

Belk Hall  |  Elm Hall  |  Greek Village  |  Hawthorn Hall  |  Holshouser Hall  |  Hunt Hall  |  Laurel Hall  |  Levine Hall
Lynch Hall  |  Maple Hall  |  Martin Hall  |  Miltimore Hall  |  Moore Hall  |  Oak Hall  |  Pine Hall  |  Sanford Hall
Scott Hall  |  Wallis Hall  |  Witherspoon Hall
 


Belk Hall, Hunt Hall, Martin Hall and Oak Hall
(Thermostat: Johnson Controls/Honeywell)

  1. Select mode auto/cool/heat/off
  2. While in heat/ cool mode use up/down arrow to select desired set point
  3. If you choose auto it will switch from cool to heat automatically based on desired set points
  4. Note there should not be no more than a 3 to 4 degree difference in set points for auto
  5. You can also select your fan function from auto to on
  6. Difference being that when it is in on fan will run 24/7, in auto it runs only when the unit is calling for heat/cooling

Elm, Maple and Pine Halls
(Thermostat: Honeywell)

These units are closed for renovations for the 2016-2017 academic year.


Greek Village

  1. Controls are locked and require a W/O to adjust temperature

Hawthorn Hall
(Thermostat: Honeywell)

  1. Set temperature dial to desired temperature
  2. Set fan speed to desired speed
  3. Unit will automatically changed from Heat/Cooling to maintain desired temperature

Holshouser Hall
(Thermostat: Schneider)

  1. Press up/down arrow unit will come up in whatever mode it is in Heat or coolingUnit will
  2. While heat or cool mode is up press the mode button to switch to the other mode
  3. Set temperature to desired level, same can be done while in each mode heat or cooling
  4. Unit will auto change to maintain desired set point

Laurel Hall
(Thermostat: Price)

  1. Use up/down arrows to pick desired set point
  2. Make sure Thermostat says saving set point
  3. Unit will automatically change from heat/cool to maintain set point

Levine Hall

  1. Set desired temperature by pushing the down button to decrease the temperature or the up button to increase the temperature.

Lynch Hall
(Thermostat: Honeywell)

  1. Turn unit on
  2. Turn fan to auto or on
  3. In auto fan will only rum when heat or cooling is called for, in on unit fan run continuously
  4. Set fan speed, 1 - low, 2 -med, 3 – high
  5. Set desired temperature with up or down arrows
  6. Unit will auto change to maintain desired temp.

Miltimore Hall
(Thermostat: Peco)

  1. Turn unit on
  2. Select fan speed
  3. Set desired temperature with thumb wheel
  4. Unit will auto change to maintain setpoint

Scott, Sandford and Moore Halls

  1. Controlled thru a BAS system, requires a W/O to adjust temp 

Wallis Hall
(Thermostat: Honeywell)

  1. Turn unit from off to auto
  2. Set cooling or heat to desired temp. Unit automatically switches to maintain desire temp
  3. Set fan to auto or on mode
  4. In auto fan will only run when heat or cooling is called for, in on unit fan run continuously  

Witherspoon Hall
(Thermostat: Honeywell)

Units 01-15, all floors:

  1. Push button under system to select mode
  2. Press up or down arrows to desired set point Slide button from off to Heat or Cool
  3. System will automatically change to maintain desired temperature
  4. Button under fan allows  you to select auto or on
  5. In auto fan will only rum when heat or cooling is called for, in on unit fan run continuously

Units 16-35, all floors:

  1. Slide button from off to Heat or cool mode
  2. Use thumbwheel to set desired temperature
  3. System will automatically change to maintain desired temp